{"product_id":"pantalla-multifuncion-canchecked-mfd15-gen2-para-volkswagen-vw-amarok-lhd-rhd-prefl-vfl-i-2010","title":"CANchecked MFD15 GEN2 Multifunction Display for Volkswagen VW Amarok LHD \/ RHD preFL vFL I 2010 -","description":"\u003cp\u003eWith the CANchecked MFD15 Gen2 display for your pre-facelift VW Amarok, left-hand or right-hand drive, you'll always have all relevant values in view.\u003c\/p\u003e\n\n\u003cp\u003eThe MFD15 Gen2 is equipped with an OLED display that offers excellent readability even in direct sunlight. Thanks to its 52mm outer diameter, the display is compatible with commercially available interior frames, even without a specific vehicle mount. Operation is via two push buttons, located on the windshield, or with the optional rotary knob.\u003c\/p\u003e\n\n\u003cp\u003eKey Features\u003c\/p\u003e\n\n\u003cp\u003eCompact design: 52mm diameter and only 12.5mm depth.\u003c\/p\u003e\n\n\u003cp\u003eFlasher: The front LED of the display can be used as a turn signal or warning LED, and is freely configurable.\u003c\/p\u003e\n\n\u003cp\u003eCAN Bus: Compatible with CAN Bus ECUs, OBD2 from 2008 and deep values for VW\/Audi from 2008, or create your own CAN stream.\u003c\/p\u003e\n\n\u003cp\u003eWLAN: Connect to your smartphone or PC and perform all subsequent steps via our web interface.\u003c\/p\u003e\n\n\u003cp\u003eAdditional inputs: Connect up to 6 analog sensors to the inputs or connect an ethanol sensor* directly to the display.\u003c\/p\u003e\n\n\u003cp\u003ePre-defined alarms: Pre-defined alarms can be easily activated and customized. For example, receive an important alert when exhaust gas temperature exceeds 900 degrees. Customization: Use your own logo or background image to customize your MFD15 Gen2.\u003c\/p\u003e\n\n\u003cp\u003eOnline logging*: Log your data with your smartphone or PC and save the log to your device for later analysis.\u003c\/p\u003e\n\n\u003cp\u003eFlex fuel*: View ethanol content and temperature on the display.\u003c\/p\u003e\n\n\u003cp\u003eCAN Switching*: Switch between CANs using the buttons on the display and send the readings from your analog inputs to the CAN bus.\u003c\/p\u003e\n\n\u003cp\u003eDifferent views\u003c\/p\u003e\n\n\u003cp\u003eChoose up to eight pages with different views and customize your display to best suit you and your vehicle:\u003c\/p\u003e\n\n\u003cp\u003eAnalog pointer\u003cbr\u003e\nDouble value\u003cbr\u003e\nGear indicator\u003cbr\u003e\nQuad values\u003cbr\u003e\nSextuple values\u003cbr\u003e\nBar + dual display\u003cbr\u003e\nRound display\u003cbr\u003e\nBar chart (dual horizontal)\u003cbr\u003e\nPerformance meter\u003cbr\u003e\nBar graph (1 to 6 vertical bars)\u003cbr\u003e\nSingle value\u003c\/p\u003e\n\n\u003cp\u003eOnline DSS - oDSS\u003c\/p\u003e\n\n\u003cp\u003eNew to our MFD15 Gen2, you can access the device via WLAN. This allows you to configure the MFD15 Gen2 from your smartphone or PC.\u003c\/p\u003e\n\n\u003cp\u003eWith oDSS, you can fully configure your display, log values (license required), upload your own start image, and update the display.\u003c\/p\u003e\n\n\u003cp\u003eSupported Values\u003c\/p\u003e\n\n\u003cp\u003eA common question from our customers is: \"What values can I request from my ECU?\" The answer: \"ALL\". Our MFD15 Gen2 is compatible with ISO 11898-2 and SAE J2284.\u003c\/p\u003e\n\n\u003cp\u003eECU manufacturers determine which values are sent via the CAN bus interface. In this case, documentation is essential, even in DBC file format that can be imported using our DSS. As a customer, you can access our extensive list of compatible ECUs. In total, depending on the manufacturer, up to 64 sensors can be queried.\u003c\/p\u003e\n\n\u003cp\u003eOBD2 queries via CAN Bus (11-bit\/29-bit) are also implemented. Vehicle-specific protocols such as UDS or TP2 are also available.\u003c\/p\u003e\n\n\u003cp\u003eIncluded by default:\u003c\/p\u003e\n\n\u003cp\u003e- OBD2 - 11 and 29-bit\u003c\/p\u003e\n\n\u003cp\u003e- Ecumaster - Classic and Black\u003c\/p\u003e\n\n\u003cp\u003e- VAG PQ34\u003c\/p\u003e\n\n\u003cp\u003e- Haltech v2\u003c\/p\u003e\n\n\u003cp\u003e- LinkECU\u003c\/p\u003e\n\n\u003cp\u003e- MaxxECU\u003c\/p\u003e\n\n\u003cp\u003e- Motec M1\u003c\/p\u003e\n\n\u003cp\u003e- Emtron\u003c\/p\u003e\n\n\u003cp\u003e- Megasquirt 2 and 3\u003c\/p\u003e\n\n\u003cp\u003eIf the desired ECU is not listed, you can download or request the corresponding TRI\/TRX from our database.\u003c\/p\u003e\n\n\u003cp\u003eFor all VW\/Audi vehicles manufactured from 2008 onwards, we offer detailed data queries by protocol. Values such as oil temperature, boost pressure, transmission temperature, cylinder-selective ignition return angle, high\/low pressure, wastegate actuation, and much more can be queried and displayed.\u003c\/p\u003e\n\n\u003cp\u003eInternal LED\u003c\/p\u003e\n\n\u003cp\u003eThe internal LED can be used as a shift light and a warning light.\u003c\/p\u003e\n\n\u003cp\u003eAs a shift light, you can assign up to 8 different colors, speed limits, and the speed at which it starts flashing.\u003c\/p\u003e\n\n\u003cp\u003eAs a warning LED, you can assign a minimum and maximum value to each sensor (in the oDSS, under \"Sensors\") and activate the corresponding LED. If the sensor exceeds the maximum value or falls below the minimum, the LED will flash in the previously configured color. Flashing is deactivated during the warning.\u003c\/p\u003e\n\n\u003cp\u003eConnection and Extension\u003c\/p\u003e\n\n\u003cp\u003eIncluded in every shipment:\u003c\/p\u003e\n\n\u003cp\u003eMFD15 Gen2 display\u003cbr\u003e\nConnector B (6-pin)\u003cbr\u003e\nConnector C (12-pin)\u003cbr\u003e\nPre-crimped 20cm connection cables for power, CAN bus, analog inputs, 5V, and sensor ground\u003cbr\u003e\nPins for crimping\u003cbr\u003e\nTwo 1 kΩ resistors (for NTC sensor pull-up)\u003cbr\u003e\nVehicle-specific vent trim\u003cbr\u003e\nOBD connection cable\u003c\/p\u003e\n\n\u003cp\u003eSensors of any type can be connected via the six analog inputs; we support 0-5V linear sensors and NTC sensors.\u003c\/p\u003e\n\n\u003cp\u003eOur in-house manufactured CAN-checked Display sensors are stored by default in the TRI\/TRX files and only need to be connected:\u003c\/p\u003e\n\n\u003cp\u003eAIN1: Temperature sensor\u003c\/p\u003e\n\n\u003cp\u003eAIN2: Transducer for K-type exhaust gas temperature probe\u003c\/p\u003e\n\n\u003cp\u003eAIN3: Pressure sensor 0-10 bar\u003c\/p\u003e\n\n\u003cp\u003eAIN4: Boost pressure sensor 0-5.5 bar absolute\u003c\/p\u003e\n\n\u003cp\u003eAIN5: Not pre-configured\u003c\/p\u003e\n\n\u003cp\u003eAIN6: Not pre-configured\u003c\/p\u003e\n\n\u003cp\u003eFor connection, you can use our pre-assembled 4-way AIN harness.\u003c\/p\u003e\n\n\u003cp\u003eIf you have the corresponding license*, you can additionally connect an ethanol sensor directly to the display via a separate pin.\u003c\/p\u003e\n\n\u003cp\u003eOptional accessories\u003c\/p\u003e\n\n\u003cp\u003eCC22501 ETK01: External rotary knob with 50cm PnP connection cable\u003cbr\u003e\nCC22100 CBD08: Eight-way CAN distribution hub\u003cbr\u003e\nCC22902 NTC01: 1\/8\" NPT liquid temperature sensor\u003c\/p\u003e\n\n\u003cp\u003eCC22903 TCC01 - K-type transducer 0-1250 °C\u003c\/p\u003e\n\n\u003cp\u003eCC22901 FLP01 - Pressure sensor 0-10 bar (145 psi) M10x1\u003c\/p\u003e\n\n\u003cp\u003eCC22900 BST01 - Pressure sensor 0-5.5 bar absolute (80 psi)\u003c\/p\u003e\n\n\u003cp\u003e*Additional Licenses\u003c\/p\u003e\n\n\u003cp\u003eReal-time logging of the MFD15 Gen2\u003c\/p\u003e\n\n\u003cp\u003eWith the additional \"Real-time logging\" license, the display can log sensor data in the oDSS. You can then download the log as a file to your smartphone or PC.\u003c\/p\u003e\n\n\u003cp\u003eAll sensors are logged (ATTENTION: for OBD and UDS, only those currently displayed are logged). Select the sensors you want to visualize graphically.\u003c\/p\u003e\n\n\u003cp\u003eEthanol sensor for flex fuel directly on the MFD15 Gen2\u003c\/p\u003e\n\n\u003cp\u003eWith the additional license for the ethanol sensor, you can connect a sensor directly to the display. You need a pull-up resistor (10 kΩ) between 5V and the signal.\u003c\/p\u003e\n\n\u003cp\u003eYou can now see the ethanol content and fuel temperature, and also log them.\u003c\/p\u003e\n\n\u003cp\u003eCAN switching and AIN forwarding\u003c\/p\u003e\n\n\u003cp\u003eWith the additional license for CAN switching and AIN forwarding, you can use the keys on your display or the rotary knob to switch CAN switches and apply the input voltages of your analog inputs to the CAN bus.\u003c\/p\u003e","brand":"CANchecked","offers":[{"title":"Default Title","offer_id":56963523903828,"sku":"CC53003","price":323.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/4701\/3460\/files\/cc53003.png?v=1788432491","url":"https:\/\/www.thetunerlab.com\/en\/products\/pantalla-multifuncion-canchecked-mfd15-gen2-para-volkswagen-vw-amarok-lhd-rhd-prefl-vfl-i-2010","provider":"Thetunerlab","version":"1.0","type":"link"}